| Applications |
Autogen |
Rotary |
| |
% |
Cat. |
| Auger—Dry
Material [Loaded start, use Cat. “B”.
May require a hard-start panel.] |
50-70 |
A,B |
| Auger—Dense/Wet Material [Loaded start, use Cat. “C”. May require a hard-start panel.] |
0 |
B,C |
| Auto Lift, Mechanical |
0 |
C |
| Auto Lift, Hydraulic |
50-70 |
B |
| Bagging Machine |
50-70 |
B |
| Balancer—Crankshaft, Drive Shaft |
90-100 |
A |
| Baler, Compaction |
0 |
B |
| Bank Vacuum System |
0 |
B |
| Battery Charger—Static [Divide charger input amps(@230v) by
3 for actual rotary hp required. Ex:
Charger 28 amps input @230v divided by 3=9.3 hp. Use Model 215 Rotary (10hp).] |
0 |
D |
| Battery Charger—Motor/Generator |
50-70 |
A |
| Bender—Pipe, Tailpipe, Tubing |
SD |
A |
| Blender |
90-100 |
A |
| Blower, Organ [Old, low RPM motors may use Autogen SD.] |
50-70 |
A |
| Blower, Air, Material Conveying |
50-70 |
B |
| Buffer |
90-100 |
A |
| Car Wash Machinery |
0 |
B |
| Center Pivot—Tower Motors [See Catalog Section on “Center Pivot
Converters.”] |
0 |
D |
| CNC Equipment [See DIGI-Series Catalog Page for Selection
Information.] |
0 |
D |
| Cold Saw, Metal Cutting |
90-100 |
A |
| Combination Loads—Motors Plus 3-Phase Heating: [Using the
guidelines, determine the converter model required for your multi-motor
load. Next, calculate your heat load
at 2 amps of 3-phase heating (@230v) per actual rotary hp. Ex: A multi-motor
load that requires a Model 215 (10hp) Rotary, plus an 18 amp heat load (18
divided by 2=9 hp) 10+9=19hp: Use Model 256 (20 hp) Rotary. |
0 |
D |
| Compactor |
0 |
B |
| Compactor w/Shear—Paper Products |
0 |
C |
| Compressor—Air/Gas [Commercial: Use SD-Series or Rotary.] |
90-100 |
B |
| Compressor—A/C, Refrigeration [See Note at Pumps: Heat, A/C
Refr.] |
0 |
B |
| Computer |
0 |
Call |
| Concrete/Concrete Block Plant [May require hard-start panel on
mixer motor.] |
0 |
C |
| Conveyor, Non-Auger [Bucket conveyor use Cat. “B” rotary.] |
90-100 |
A,B |
| Dairy—Milking Machine |
50-70 |
B |
| Die Cutter, Cardboard |
0 |
B |
| Dishwasher |
50-70 |
A |
| Door Opener, Automatic |
50-70 |
B |
| Drill Press |
90-100 |
A |
| Dry Cleaning Equipment |
0 |
B |
| Dumb Waiter |
90-100 |
A |
| Edge Bander—Motor & Heat Load [See Note at Combination
Loads—Motors Plus 3-Phase Heating: Motors are Cat. A.] |
0 |
D |
| Elevator—Hydraulic, Cable |
0 |
B |
| Embroidery Machine |
0 |
A |
| Engraving Machine |
50-70 |
B |
| Fan—Exhaust, Heat, etc. [See Grain Dryer Note.] |
50-70 |
A,B |
| Fertilizer Plant. [Some blender motors require a hard-start
panel.] |
0 |
B,C |
| Flood Gate |
50-70 |
B |
| Flywheel Loads [See also Hammer mill.] |
90-100 |
A,B |
| Food Service Equipment |
90-100 |
B |
| Garage Door Opener |
90-100 |
A |
| Garbage Disposal Unit |
90-100 |
A |
| Gear Hobber |
50-70 |
B |
| Grain Dryer [Single-Fan: Cat. “B”, Multi-fan: Cat. “C”. May also
require Kilogen Module.] |
0 |
B,C |
| Grinder-Mixer, Farm |
0 |
B |
| Grinder, Pedestal |
90-100 |
A |
| Grinders, Surface, Crankshaft, Centerless |
50-70 |
B |
| Guide & Seat Machine—Engine Machining |
90-100 |
A |
| Hammer Mill [May require Hard-Start Panel] |
0 |
B |
| Heat, Oven, Lighting [if possible, connect heat/lighting to
single phase. Otherwise, use 2.5
Actual Rotary hp per kW] |
0 |
D |
| Hog Houses, Automatic [Install single-phase motors] |
0 |
0 |
| Hoist—Motor Winch, Chain or Cable |
90-100 |
B |
| Ice Cream Machine, Soft Serve [Add tub(auger) and compressor hp
for start load. See note at Pumps:
Heat, A/C, Refr.] |
0 |
C |
| Ice Maker [See Note at: Pumps: Heat, A/C, Refrigeration.] |
0 |
B |
| Ironworker, Hydraulic |
50-70 |
B |
| Ironworker, Mechanical |
90-100 |
A |
| Lathe, CNC [See DIGI-Series] |
0 |
D |
| Lathe w/Clutch |
90-100 |
A |
| Lathe, High Speed, No Clutch [Rotary may require a hard
start panel] |
0 |
B,C |
| Laser [Multiply laser kW (Kilowatts) by 2.2 for DIGI-Series
rotary kVA] |
0 |
D |
| Laundry Extractor [Multi-Machine: 3 to 4 washers run on class”C”
rotary] |
0 |
B |
| Life-Support Equipment [DO NOT OPERATE ON OUR PHASE CONVERTERS] |
0 |
0 |
| Machine Shop, Multi-Motor |
90-100 |
B |
| Meat Grinder [Commercial Use/Frozen meat: Use rotary] |
90-100 |
A |
| Milling Machines, Non-CNC |
90-100 |
A |
| Mixer, Food Processing |
90-100 |
B |
| Molding Machine, Plastic Injection [Motor load, Cat. “B” then
add 3-phase heat load. See,
Combination Loads Note] |
0 |
D |
| Molding Machine, Wood |
0 |
B |
| Pallet Notcher |
0 |
C |
| Paper Folder |
50-70 |
A |
| Paper Shear |
0 |
B |
| Pipe Threader |
0 |
B |
| Planer |
50-70 |
B |
| Poultry Fans, Poultry House, Automatic |
0 |
B |
| Press, Press Brake: Mechanical |
90-100 |
A |
| Press, Press Brake: Hydraulic |
0 |
B |
| Printing Press [Jogging, Cat. “C”] |
0 |
B |
| Pumps: Any Pump using big U.S. Brand Uni-Mount Motors (25hp or
larger) |
0 |
Call |
| Pumps: Automatic [See Pumps, Sewage Lift note] |
50-70 |
B,C |
| Pumps: Centrifugal [Centrifugal, turbine or VHS pumps operating
@ service factor 1.15 use Cat. “B”. In service factor 1.25, Cat “C”. Others: Single pump: Cat. “A” with Kilogen;
or Cat. “B”, no Kilogen. 2 pumps: Cat.
B with Kilogen; or Cat. “C”, no Kilogen] |
50-70 |
D |
| Pumps: Heat, A/C, Refrigeration [Hermetic compressors may
have two motor amperage designations: RLA, or Run Load Amps, and LRA, or
Locked-Rotor Amps. Divide RLA by 2.5
for hp, then use a rotary converter from load category “B”. If RLA is not stamped on the compressor,
find LRA of compressor (stamped on Compressor housing) and consult the
factory. When multiple refrigeration
compressors of the same hp are operated, increase converter size one step for
each additional compressor. Es: A
quantity of 5 hp compressors (14 amps RLA each) use a Model 215 for one,
Model 254 for 2, or a Model 256 for 3.
Please note that the minimum circuit amps required for the operated
machine is not the same as the compressor RLA.] |
0 |
B |
| Pumps: Irrigation [See: Pumps: Centrifugal note] |
50-70 |
A,B |
| Pumps: Manure |
50-70 |
C |
| Pumps: Oil Well Pump Jack |
90-100 |
B |
| Pumps: Pressure Washer [See Note at Pumps: Centrifugal; re
Service Factor] |
0 |
B |
| Pumps: Sewage Lift [See Catalog section “Phase Converters with
Automatic Controls”] |
0 |
B,C |
| Pumps: Submersible, to 10 hp |
0 |
B |
| Pumps: Submersible, 15 hp and up |
0 |
C |
| Pumps: Swimming Pool |
0 |
A,B |
| Pumps: Turbine, Vertical [See Note at Pumps: Centrifugal] |
0 |
A,B |
| Pumps: Trash, Drainage |
0 |
B |
| Pumps: Vertical Hollow Shaft [See Note at Pumps:
Centrifugal] |
Call |
B |
| Punch Press |
90-100 |
A,B |
| Rectifier/3-Phase SCR Load [Sized at 1.8 amps load (@230v)
per rotary hp. Ex: A 9 amp Rectifier uses a 5 hp (Model 184) rotary since 9
divided by 1.8 = 5] |
0 |
D |
| Rock Crusher |
50-70 |
B |
| Sander, Edge |
90-100 |
A |
| Sander, Belt/Wide Belt |
50-70 |
A |
| Saw Mill |
0 |
B,C |
| Saws: [on Commercial Use, the Rotary saves many man-hours labor] |
|
|
| Abrasive (Cut-Off) |
90-100 |
B |
| Saws: Automatic |
50-70 |
B |
| Saws: Band Type: Meat, Metal, Wood |
90-100 |
A |
| Saws: Marble-Cutting |
50-70 |
B |
| Saws: Radial Arm, Table |
90-100 |
A |
| Saws: Stone/Masonry/Tile |
90-100 |
A |
| Sewing Machine |
90-100 |
A |
| Shaker |
50-70 |
B |
| Shear, Hydraulic |
0 |
B |
| Shear, Mechanical |
90-100 |
B |
| Sheet Metal Equipment |
50-70 |
B |
| Shrink-Wrap Machine—Vacuum Form [This is a motor and heat
load. See Note at Combination
Loads—Motors Plus 3-phase Heating.
Figure your vacuum pump motor @ Cat. “B”] |
0 |
D |
| Siren—Fire, Civil Defense |
Call |
B |
| Ski Tow or Lift |
0 |
B |
| Slitter |
90-100 |
B |
| Thermo-King Unit/Land & Sea Container [Belt Drive Comprssor
use SD, Hermetic See Note at Pumps: Heat, A/C, Refr.] |
SD |
B |
| Transmitter, Broadcast [Use DIGI-Series rotary converter,
1.7 amps of transmitter input power per rotary kVA @ 230v. Ex: 50 amp
transmitter divided by 1.7 = 29.4 kVA.
Use 30 kVA DIGI 286 rotary] |
0 |
D |
| Truck Refirgeration |
SD |
B |
| Turntable |
90-100 |
A |
| Vacuum Forming Machine [This is a motor and heat load. See Note at Combination Loads—Motors Plus
3-phase Heating. Figure your vacuum
pump motor @ Cat. “B”] |
0 |
D |
| Valve Opener Motor |
SD |
A |
| Vibrator |
50-70 |
B |
| Welder, Motor Generator |
90-100 |
A |
| Welder, Transformer [Divide welder input amps by 3 (@230v)
for actual rotary hp. Ex: 20 amp input welder divided by 3 = 6.67 hp. Use DP 215 Rotary] |
0 |
D |
| Wheel Balancer [Computerized spin balancers use WB-Series static
converters] |
90-100 |
A |
| Woodworking Shop |
50-70 |
B |
| X-Ray Machine [Use 1kVA of DIGI-Series rotary for every 1.8
amps x-ray @230v. Ex: 15 amp x-ray divided by 1.8 = 8.33 kVA. Use Model DIGI 215 (10 kVA) rotary] |
0 |
D |
|
|
|
